Renewable energy sources can have as many applications as imaginable. Among them, pumping water among other possible uses, for example for its use for irrigation.
how to get portal eco inventionsan alternative to performing this operation without causing an increase in energy consumption make a wind water pump, provides the energy necessary to raise this source. We explain how to build this mechanism, where you will basically need skill and reused parts from old bikes.
Wind water pump instructions.
Step 1: Prepare the wheels and gear.
Most of the materials of this wind powered water pump used bike partsis adapted to work for this purpose. This is the case with gears where you have to use the piece (cassette) you see in the picture and place a bolt around it as you can see.
Use short bolts for the part that will go on top of the pump; For those who go vertically, long ones will be more suitable.
Next, attach the horizontal gear to the axle of a bicycle wheel. On the other hand, attach the piece to the rim of another wheel with three metal supports.
Now you will need a sturdy tripod to secure a T-piece at the top for the connection of PVC pipes. In this piece, you will need to set up the wheel structure you created. In this case, we chose to do it with a few circular pieces of wood. Then, you should attach the vertical part to the horizontal part of the PVC terminal in such a way that it does not prevent it from turning.
Step 2: Build the wind sails.
Although initially pieces of cloth covered with plastic covers were chosen for this project, the truth is that after several tests the system was found to be not effective enough. So prepare five wind sails with PVC or tin and fix them directly on the tires of the bike.
Step 3: Attach the sails.
In this step, you’ll need to drill five holes big enough for a bicycle wire to run through. In fact, you will need to place them on the rim for them to bond well, for example, with epoxy, which is commonly used in plumbing due to its adhesion effectiveness.
The sails will also need to be attached to the spokes of the bike after the epoxy has dried. Fix it again with the same material and if you want to further strengthen the structure, screw the spokes to prevent the sails from falling.
Step 4: Produce the pump connector.
If you check the vertical mechanism, you will see that there is a small red ball behind the bolts you have attached to the cassettes. Actually, there are two of them, this one and the other fixed on the piston of the water pump, so that the wind generator and the pump are connected, so that the power of the wind is transferred to the water pump.
This connector is simply made of a PVC pipe. For example, a few bicycle wires were placed inside by heating only the plastic over a kitchen fire. Make sure this part of the system is as light as possible, otherwise it will need more air to operate.
Step 5: Build the water bomb.
You will basically need PVC pipe and a T-connector to build the water pump. If you follow the pattern in the image, you should have no problem getting everything to fit. You can also refer to this video to help you with this step.
Step 6: Fix the wind turbine and water pump.
Securely fix a metal rod to the floor where you want to place the equipment so that the system stands upright. Attach the metal rod to the outside of the pump using the vise clips.
Next, place the wind turbine on top of the pump so that the connecting rod can be fully extended. Finally, be sure to connect the union with the wheel horizontally and with the piston of the pump.
As the system can be a little fragile, Ideally, you should strengthen it by installing it on a 4×4 pole, It will eliminate unwanted movement.
With all these steps, the wind water pump will be ready. But after observing its operation and receiving many suggestions, the proponent of this idea has implemented some of them. Enhancements to improve performance. These are:
-
Replace the tripod with a metal tube throughout the entire system.
-
Move the valve closer to the ground so you don’t have to pump the water that high.
-
Replace the PVC piston and rod with bicycle shock absorbers.
-
Remove the sails from the bottom and leave them attached to the upper structure so they stay in ‘attack mode’ which will provide more flexibility and support propulsion.
Now, with these final recommendations, you’re all set to get your wind powered air pump up and running.
If you have any questions, here is the project and complete instructions: instructionables.com
…….
Reference article: https://ecoinventos.com/como-fabricar-bomba-de-agua-eolica-paso-a-paso/
……
Contact address of the environment department: [email protected]